Bushings, holders & clamps made for steel framing
SnapSet Holders are a new generation of bushings, holders, clamps, dividers and pipe guides designed around the realities of MEP rough-in in light gauge steel.
THE WORKHORSE HOLDER
Universal Bushing Holder
SKU: HD008-1-P-UBH1
The workhorse of the SnapSet system. The UBH gives electricians and plumbers a secure, flexible way to route wire, cable and pipe through steel framing — horizontally, vertically, or turning direction. Fit up to 4× as many wires in one UBH as with traditional bushings.
| Provides for cable or pipe attachment at every bushing. |
| ⅜" offset base keeps cable and pipe clear of the stud. |
| Snip the flanges to make two separate holders. |
| Eliminates protection plates at 3½" and 3⅝" studs. |
THE SUPPORT HOLDER
Round Bushing Holder
SKU: HD008-1-P-RDBH
A bushing & holder for industry standard round openings that provides abrasion protection while offering multiple points to position, support, and secure cables or pipes.
| Provides for cable or pipe attachment at every bushing. |
| 3⁄8" offset base keeps cable and pipe clear of the stud. |
| Eliminates protection plates at 3½" and 3⅝" studs. |
ACCESSORY
BH Clamp
SKU: HD008-2-P-CLMP
Snaps into AssemblyBuilt Bushing-Holders to secure cables or pipes parallel to the framing member.
| Secures ½"–¾" pipe and any cable |
| Snaps in, no tools |
| Works with both holders |
ACCESSORY
Pipe Guide
SKU: HD008-2-P-PIPE
Snaps into AssemblyBuilt Bushing-Holders to supports and guide ½” pipe while allowing for expansion and contraction.
Note: All AssemblyBuilt Bushing-Holders have built-in support for 3/4" pipe.
| Guides and supports ½" pipe |
| Allows for expansion & contraction |
| Meets IPC 305 & 308 |
ACCESSORY
CABLE DIVIDER
SKU: HD008-2-P-DIVI
Snaps into Bushing-Holder to split one opening into two separate cavities, keeping multiple cables organized.
| Splits one opening into two cavities |
| Separates cable for heat or voltage |
| Snaps in before or after cable |
Why SnapSet?
SPEED
Keep the crew moving. Purpose-built components make common rough-in tasks measurably quicker and easier for your tradespeople.
FLEXIBILITY
Work with the frame, not against it. Multiple ways to route, secure and organize MEP give crews options when the field doesn't match the drawing.
QUALITY
Get it right the first time. Secure, consistent installations help reduce damage, rework and downstream trade conflicts.
No tools, no screws.
1. Align
Line the holder up with the service hole
from the back side of the stud.
2. Snap
Pull it through from the front until
it snaps securely into place — no tools, no screws.
3. Secure
Run cable or pipe through. Lock with a UBH Clamp
or ziptie snap in a Divider or Pipe Guide.
Need two smaller holders? Snip the UBH flanges at the midpoint to create two separate bushing holders from one part.
Frequently asked
questions
What framing does SnapSet fit?
Standard service holes in 11–25 ga light-gauge steel from Clark Dietrich, FRAMECAD, Howick, Scottsdale and Arkitech — ovals from 1½"×3" to 1½"×4", and 1-3⁄8" round holes.
Do I need tools to install it?
No. Every SnapSet part snaps in by hand — no tools and no screws — and the clamp, divider and pipe guide snap into the holders the same way.
What can I run through it?
NM, MC, AC and low-voltage cable, plus ½" and ¾" copper, PEX, PVC, CPVC and poly pipe.
How do I get SnapSet or request pricing?
SnapSet is launching now. Get on the list for pricing, samples and availability, or request a quote and we'll follow up.
Put SnapSet to work on your next steel frame job.
Get on the list for pricing, samples and availability — or come see it installed live at MetalCon.